Journal
How a certificate of analysis is structured
A certificate of analysis is more than a table full of numbers. Once you know how it is organised and which question each section answers, you can judge what a COA actually tells you within a few minutes.
By Redaktion GOLDKERN (Demo)Published on September 29, 2026Expert review: Expert review pending
Anyone who works with research material will sooner or later be handed a certificate of analysis, or COA. At first glance the document looks like a table full of abbreviations. In fact it follows a clear logic: it links a specific batch to the tests carried out on it and to the criteria against which the results are measured. This article works through the typical sections in turn.
One batch, one certificate
The most important principle first: a COA applies only to the batch whose number it bears. Even if two batches of the same product were made by the same process, their purity, peptide content or water content may differ. A certificate without a batch number, or with a number that does not match the label, therefore tells you nothing about the sample in front of you.
Header and identification
The header shows the issuing body, a document number and the date of issue. Below it comes the identification of the substance: the product name, the amino acid sequence in the case of peptides, and the molecular formula and molecular weight. Good certificates also state the salt form, such as trifluoroacetate or acetate. This is more than a formality – whether the molecular weight refers to the free peptide or to the salt changes every subsequent concentration calculation.
The test table
At the heart of the document is a table with at least four columns:
| Column | Content |
|---|---|
| Test item | What was tested, for example identity or purity |
| Method | How it was tested, such as ‘RP-HPLC, UV 214 nm’ or a reference to a standard operating procedure |
| Specification | The acceptance criterion defined in advance |
| Result | The value measured for the batch, with its unit |
What matters is how the columns work together. A result without a method cannot be interpreted, because HPLC purity, for instance, depends on the column, gradient and wavelength. A result without a specification does not tell you whether the batch meets the requirements.
Identity, purity, content – three different questions
For peptides, the usual test items answer different questions that are easily confused:
- Identity: Is the right substance present? This is usually established by mass spectrometry, comparing the measured mass with the mass calculated from the sequence.
- Purity: What share of all chromatographically detected components does the target sequence account for? It is normally given as area per cent from HPLC.
- Content: How much of the weighed material is actually peptide? This figure also takes account of water and counterions, which do not appear in HPLC purity.
A COA may show very high purity while the peptide content is considerably lower. This is not a contradiction but a consequence of the different reference quantities.
Additional tests
Depending on the intended use, a certificate may include further test items: water content by Karl Fischer titration, counterion content, residual solvents, heavy metals or endotoxins. Endotoxins are usually reported in endotoxin units per unit of mass, determined by the LAL test or a recombinant method. A sober reading is essential here: anything not in the certificate was not tested. A missing endotoxin value does not mean that the batch is free of endotoxins – only that the document makes no statement about them.
Assessment and release
The certificate ends with an assessment of whether the batch meets all specifications and with release by a responsible person, giving name, position, date and signature. In electronic documents the handwritten signature is often replaced by an electronic signature or a release note. Many certificates also include attachments with chromatograms and mass spectra. These excerpts from the raw data are valuable because they show how the results were obtained – whether further signals appear alongside the main peak, for example.
What to check when reading a COA
A short checklist helps to assess a COA in a few minutes:
- Compare the batch number on the COA with the label.
- Check that a method and a specification are given for every result.
- Pay attention to units and reference quantities, especially for content and purity.
- Check the dates for plausibility: manufacture, testing, issue, retest.
- Look at the attachments, if there are any.
- Archive the certificate together with your own experimental data.
What a COA does not do
A certificate of analysis is not a safety data sheet. It contains no information on hazards, protective measures, storage or disposal; that belongs in the safety data sheet. Nor does a COA confirm that a material is suitable for a particular experiment. It documents which results a specific batch achieved in specific tests – no more, but also no less. It is precisely this limitation that makes it a reliable building block of traceable research.
Sources
The sources for this article are being verified by the editorial team and will appear once verified.
- Quality
- Analytical methods
- Documentation