Skip to content

Intended useFor research use only. Not for human or veterinary use.

Journal

Storing lyophilised peptides in the lab: fundamentals

Lyophilisates are considered robust – as long as they stay dry, cold and dark. Which factors determine stability, which amino acids are particularly sensitive, and how storage can be organised properly in day-to-day lab work.

By Redaktion GOLDKERN (Demo)Published on September 29, 2026Expert review: Expert review pending

Most research peptides arrive in the laboratory as a lyophilisate: a dry, loose powder or a porous cake at the bottom of a vial. In this form peptides are, as a rule, considerably more stable than in solution. Stable, however, does not mean unchanging. How long a lyophilisate retains its quality depends on the sequence, the residual moisture and, above all, on how it is stored and handled. This article summarises the fundamentals. The product- and batch-specific information on the data sheet always takes precedence.

Why dryness protects

Most degradation pathways of peptides are chemical reactions that require water and molecular mobility: hydrolysis of peptide bonds, deamidation of asparagine and glutamine, rearrangements at aspartic acid. Freeze-drying removes most of the water from the material and severely restricts the mobility of the molecules, which slows these reactions down considerably. This advantage is gradually lost, however, as soon as the hygroscopic powder takes up moisture from its surroundings.

The four most important factors

  • Moisture: the single most important factor. Every time a cold vial is opened in warm room air, condensation can get in.
  • Temperature: chemical reactions proceed more slowly at lower temperatures. Common laboratory practice for the long-term storage of lyophilisates is therefore freezing at −20 °C or below.
  • Light: aromatic amino acids such as tryptophan and tyrosine can be altered by light, especially its UV component. Amber glass or light-tight packaging reduces this risk.
  • Oxygen: methionine, cysteine and tryptophan are susceptible to oxidation. For such sequences it can make sense to blanket the vial with an inert gas such as argon or nitrogen after opening.

The sequence has a say

Not every peptide is equally sensitive. A look at the sequence shows what to watch for:

Motif or amino acidPossible change
Met, Cys, TrpOxidation; for cysteine also disulfide formation
Asn, especially Asn-GlyDeamidation
Asp, especially Asp-Gly and Asp-ProIsomerisation to isoaspartate or chain cleavage
N-terminal GlnCyclisation to pyroglutamate

These reactions proceed much faster in solution than in the dry state. For storage, this means that the more sensitive motifs a sequence contains, the more rigorously moisture, oxygen and heat should be kept away.

Goods receipt and storage

Storage begins at goods receipt. Whether a short journey without refrigeration is uncritical depends on the sequence; what matters is getting the material into the intended conditions promptly after it arrives. It is good practice to record:

  • product, batch number and date of receipt,
  • condition of the packaging and closure,
  • appearance of the contents,
  • storage location and intended storage temperature.

For long-term storage, freezers without an automatic defrost function are better suited than frost-free models, whose defrost cycles cause brief, regular rises in temperature. A temperature log makes deviations visible.

Taking material out properly

Many quality losses occur not in the freezer but when material is taken out. The following routine has proved its worth:

  1. Take the sealed vial out of the freezer and let it reach room temperature in a desiccator, or at least with the closure in place.
  2. Only then open it, remove the required amount promptly and reseal the container immediately.
  3. For oxidation-sensitive sequences, blanket the vial with inert gas before resealing.
  4. Return the vial to storage without delay and document the removal.

If the same material is needed frequently, it is worth dividing the dry powder into several small containers once. This keeps the main stock unopened.

Once the peptide is in solution

After reconstitution the situation changes fundamentally. Dissolved peptides are far less stable, and every freeze–thaw cycle can promote aggregation. Solutions are therefore divided into single-use portions, frozen and thawed only once each. The pH also plays a part: deamidation proceeds faster under basic conditions. Every aliquot is labelled with the substance, batch, solvent and date.

Recognising changes

A lyophilisate that appears collapsed, clumped, sticky or discoloured has probably taken up moisture or been exposed to unfavourable conditions. Such material should not simply be used. It is advisable to document the observation and, if necessary, check the quality analytically, for example by HPLC.

In brief

Dry, cold, dark and opened as rarely as possible – with these four principles, the quality of lyophilised peptides can be preserved for a long time. Combined with clear documentation of the batch, storage location and removals, storage itself becomes a traceable part of the experiment.

Sources

The sources for this article are being verified by the editorial team and will appear once verified.

  • Storage & handling
  • Peptides
  • Fundamentals
All articles